KE300A-08 Series Instantaneous Stop Non-Stop Ball Mill Special Inverter

KE300A-08 special inverter for instantaneous stop and non-stop, with DC bus voltage as its core control principle, using this high-performance control algorithm to maximize the utilization efficiency of DC bus voltage. After comprehensive analysis process according to the measured value of the DC bus voltage, automatically adjust the driver output state to establish a reasonable load feedback energy distribution relationships, which can maintain the drive controller without power off for 4 to 9 seconds. When the drive is completely powered off and there is no display, the power grid can automatically restart after power supply. The driver does not report a fault during the entire instantaneous power failure.

Features
Specifications
Selection table
Classic Case
Download

Features of KE300A-08 Series Instantaneous Stop Non-Stop Ball Mill Special Inverter

(1) DSP high-speed control core

The control core adopts the high-speed digital processor DSP produced by TI (Texas Instruments). Ensure the system has strong performance with high speed and stability features. It can completely deal with the most complex control operations.

(2) New No PG vector control technology

No PG vector control can block the motion, the rated torque can up to 150% when it is 0.5Hz ; It can help to reduce the sensitivity to motor parameters and improve the adaptability at the site. It also can be applied to winding control, That's a perfect solution for multiple motors drag the same load.

(3) Characteristics of "excavator"

(4) Fast dynamic response

The dynamic response time under PG vector control is less than 20ms.

(5) Fast current limiting function

(6) Accurate parameter identification ability

(7) High torque control accuracy

Specifications of KE300A-08 Series Instantaneous Stop Non-Stop Ball Mill Special Inverter

Item	Technical Index	Specification
Input	Input voltage	3AC 380V±15%
Input	Input frequency	47~63Hz
Output	Output voltage	0～rated input voltage
	Output frequency	V/f control: 0~3000HzSensorless vector control: 0~300Hz
	Operation command mode	Keypad controlTerminal controlSerial communication control
	Frequency setting mode	Digital setting, analog setting, pulse frequency setting, serial communication setting, multi-step speed setting & simple PLC, PID setting, etc. These frequency settings can be combined & switched in various modes.
	Overload capacity	G model: 150% 60s, 180% 10s, 200% 3s P model: 120% 60s, 150% 10s, 180% 3s
	Starting torque	0.5Hz/150% (SVC); 1Hz/150% (V/f)
	Speed adjustment range	1:100 (SVC), 1:50 (V/f)
	Carrier frequency	1.0-16.0kHz，automatically adjusted according to temperature and load characteristics
	Frequency accuracy	Digital setting: 0.01HzAnalog setting: maximum frequency * 0.05%
	Torque boost	Automatically torque boost; manually torque boost: 0.1%~30.0%
	V/f curve	Three types: linear, multiple point and square type (1.2 power, 1.4 power, 1.6 power, 1.8 power, square)
	Acceleration/decele ration mode	Straight line/S curve; four kinds of acceleration/deceleration time, range: 0.1s~3600.0s
	DC braking	DC braking when starting and stoppingDC braking frequency: 0.0Hz~maximum frequency, braking time: 0.0s~100.0s
	Jog operation	Jog operation frequency: 0.0Hz~maximum frequencyJog acceleration/deceleration time: 0.1s~3600.0s
	Simple PLC & multi-step speed operation	It can realize a maximum of 16 segments speed running via the built-in PLC or control terminal.
	Built-in PID	Built-in PID control to easily realize the close loop control of the process parameters (such as pressure, temperature, flow, etc.)
	Automatic voltage regulation	Keep output voltage constant automatically when input voltage fluctuating
Control Function	Common DC bus	Common DC bus for several inverters, energy balanced automatically
	Torque control	Torque control without PG
	Torque limit	“Rooter” characteristics, limit the torque automatically and prevent frequent over-current tripping during the running process
	Wobble frequency control	Multiple triangular-wave frequency control, special for textile
	Timing/length/counting control	Timing/length/counting control function
	Over-voltage & over-current stall control	Limit current & voltage automatically during the running process, prevent frequent over-current & over-voltage tripping
	Fault protection function	Up to 30 fault protections including over-current, over-voltage, under-voltage, overheating, default phase, overload, shortcut, etc., can record the detailed running status during failure & has fault automatic reset function
Input/output terminals	Input terminals	Programmable DI: 7 on-off inputs, 1 high-speed pulse input 2 programmable AI: AI1: 0～10V or 0/4～20mA A12: 0～10V or 0/4～20mA
	Output terminals	1 programmable open collector output: 1 analog output (open collector output or high-speed pulse output) 2 relay output 2 analog output: 0/4~20mA or 0~10V
	Communication terminals	Offer RS485 communication interface, support MODBUS-RTU communication protocol
Human machine interface	LED display	Display frequency setting, output frequency, output voltage, output current, etc.
Human machine interface	Multifunction key	QUICK/JOG key, can be used as multifunction key
Environment	Ambient temperature	-10℃～40℃, derated 4% when the temperature rise by every 1℃(40℃～50℃).
	Humidity	90%RH or less (non-condensing)
	Altitude	≤1000M: output rated power, ＞1000M: output derated
	Storage temperature	-20℃～60℃
	Storage environment	Indoor, no direct sunlight, dust, corrosive gas, flammable gas, oil mist, steam, dripping water, salt, vibration

Model	Motor			Rated Input Amperage（A）		Rated output Amperage（A）
	kW		HP
3AC 380V -15%~15%
KE300A-08-0R7G/1R5P-T4		0.75/1.5	1/2	3.4/5.0	2.1/3.8
KE300A-08-1R5G/2R2P-T4		1.5/2.2	2/3	5.0/6.8	3.8/6
KE300A-08-2R2G/004P-T4		2.2/4.0	3/5	6.8/10	6/9
KE300A-08-004G/5R5P-T4		4.0/5.5	5/7.5	10/15	9/13
KE300A-08-5R5G/7R5P-T4		5.5/7.5	7.5/10	15/20	13/17
KE300A-08-7R5G/011P-T4		7.5/11	10/15	20/26	17/25
KE300A-08-011G/015P-T4		11/15	15/20	26/35	25/32
KE300A-08-015G/018P-T4		15/18.5	20/25	35/38	32/37
KE300A-08-018G/022P-T4		18.5/22	25/30	38/46	37/45
KE300A-08-022G/030P-T4		22/30	30/40	46/62	45/60
KE300A-08-030G/037P-T4		30/37	40/50	62/76	60/75
KE300A-08-037G/045P-T4		37/45	50/60	76/90	75/90
KE300A-08-045G/055P-T4		45/55	60/75	92/113	90/110
KE300A-08-055G/075P-T4		55/75	75/100	112/157	110/150
KE300A-08-075G/090P-T4		75/90	100/125	157/180	150/176
KE300A-08-090G/110P-T4		90/110	125/150	180/214	176/210
KE300A-08-110G/132P-T4		110/132	150/175	214/256	210/253
KE300A-08-132G/160P-T4		132/160	175/210	256/307	253/304
KE300A-08-160G/185P-T4		160/185	210/250	307/350	304/340
KE300A-08-185G/200P-T4		185/200	250/260	350/385	340/377
KE300A-08-200G/220P-T4		200/220	260/300	385/430	377/423
KE300A-08-220G/250P-T4		220/250	300/330	430/468	423/465
KE300A-08-250G/280P-T4		250/280	330/370	468/525	465/520
KE300A-08-280G/315P-T4		280/315	370/420	525/590	520/585
KE300A-08-315G/350P-T4		315/350	420/470	590/665	585/650
KE300A-08-350G/400P-T4		350/400	470/530	665/785	650/720
KE300A-08-400G/450P-T4		400/450	530/600	785/840	720/820
KE300A-08-450G/500P-T4		450/500	600/660	840/880	820/900
KE300A-08-500G/560P-T4		500/560	660/750	880/980	900/1000
KE300A-08-560G/630P-T4		560/630	750/840	980/1130	1000/1100
KE300A-08-630G/710P-T4		630/710	840/950	1130/1290	1100/1250

File Name File Format Update Date Download

Leave us Message

Products

Applications

Company News